Cadet CEC163TW Guía de instalación descargar pdf (Pagina 5)

INSTALLATION INSTRUCTIONS (continued)

__________________________

Part Two

__________________________

Determine Supply Voltage

STEP 1

Select Proper Heater Voltage

STEP 2

For 240-Volt conguration:

The Energy Plus Heater is factory congured for 240-Volt opera-

tion with a “black key” (Figure 5). Proceed to STEP 3.

Before operating, verify that the heater is congured for correct supply voltage and circuit load. The Energy Plus heater is congured for

240-Volt operation by default. For 120-Volt installation, you must switch the supplied “keys” (see Step 2) to easily congure the heat-

er to the same voltage as the supply wires. The volt sensor can assist you in conrming correct installation, after installing the heater

assembly (Step 3). Don’t worry: if you install incorrectly, you can safely recongure the heater using the Fault Code Chart on page 7

without damaging the heater.

For 120-Volt conguration:

Remove the supplied “black key” (FIGURE 6) located on the side

of the heater. Replace with the provided “white key” as shown in

Figure 7.

CORRECT 240 VOLT

CONFIGURATION (DEFAULT)

REMOVE KEY CORRECT 120 VOLT

CONFIGURATION

A qualied or dedicated circuit from circuit breaker panel is required.

Figure 5

Figure 7Figure 6

How do I insert the heater assembly into the wall can?

Install Heater Assembly

STEP 3

Install Grill

STEP 4

Align push buttons and digital display with grill cutouts before tightening with grill screws provided. Do not overtighten (See Figure 11).

Turn heater assembly so that the front of it is facing the oor (element down with motor facing you). You can then rest bottom edge of

the heater assembly on the bottom of the wall can while supporting the edge closest to you. (See Figure 8).

Connect the supply wires to the heater wires with connectors (See Figure 9 or Figure 9a). Now rotate heater assembly into wall can so

that the bottom edge drops into the half round slots in bottom lip of wall can (See Figure 10).

IMPORTANT: Push wires into bottom and left side of wall can during insertion. Be sure supply wires are not caught between motor and

wall can.

After conrming that the bottom edge of heater is positioned in the slots in bottom lip of wall can, attach assembly at top with screw

provided.

Conrm your Supply Voltage and Proper Installation

STEP 5

Turn electrical power back on at the circuit breaker or fuse box. WAIT 10-15 seconds for heater to power-up before pushing any but-

tons. The Energy Plus heater is equipped with a smart sensor that will indicate if the voltage does not match your key conguration.

Review the digital display to conrm if you have congured the heater to match the supply voltage. The heater will not operate if it is not

congured correctly.

If the heater has been congured to the correct circuit:

Display backlight will come on and read “88” for a moment; then will display actual temperature if in NO HEAT mode; ash the tempera-

ture set point if in HEAT mode; or 1,2,3 if in FAN ONLY mode. After 10 seconds, room temperature will be displayed.

Proceed to OPERATING YOUR HEATER.

If the heater has been congured to the incorrect circuit or improperly installed, a code will display. See Fault Codes, page 7.

Figure 8 Figure 9 Figure 9a

Figure 10

Figure 11

(Single Heater

120/208/240V)

(Multiple Heaters on a branch cir-

cuit, 208 or 240V ONLY)

Page 5

Black Wire Key

White Wire Key

Wiring

to Other

Heater

Field

Wiring to

Breaker

1 2 3 4 5 6 7 8 9 10 ... 15 16

Comentarios a estos manuales

Sin comentarios

Cadet CEC163TW Guía de instalación Pagina 5

Comentarios a estos manuales

Relacionado con productos y manuales para Calentadores espaciales Cadet CEC163TW