Cadet CEC163TW Guía de instalación descargar pdf (Pagina 6)

OPERATING INSTRUCTIONS

NO FAN

NO HEAT

FAN

ONLY

SLEEP

HEAT

WARNING Risk of Electrical Shock and Fire.

The heater must be properly installed before it is

used.

1. Do not operate without grill.

2. Keep electrical cords, drapery, furnishings and

other combustibles at least 3 feet away from the

front of the heater and 6 inches away from the

sides.

3. Do not tamper with the over temperature limit

control.

4. If the heater over temperature limits trip more

than once per day, the heater must be replaced.

5. Clean heater at least every six months.

6. After allowing the heater to cool, turn power off

at circuit breaker panel before removing grill.

7. Use a hair dryer or vacuum on blow cycle to

blow debris through the top element (do not touch

element).

8. Install the grill before turning on power.

WARNING: Any other service not detailed in

this Owner’s Guide should be performed by an

authorized service representative.

Digital Display

Control Buttons

Heater Modes

Setting Desired Heating Temperature

Programming Your Night/Away Button

Max/Min Temperature Lock

Energy Saving Tips

• Set your Night/Away set point to as low as you are com-

fortable, for a cooler nighttime temperature.

• When you exit the room or leave your home, push the Night

button to drop the temperature set point.

• If your heater is positioned in a drafty area or exposed to

direct sunlight, temperature reading will be affected. Set tem-

perature to desired comfort level, not a “number” on the digital

display.

• If you will be away for an extended period of time (and have

no concerns about freezing conditions), turn the rocker switch

to NO HEAT for even greater energy savings.

You can preset a night or away temperature

set point, for quick and easy “one-touch”

energy savings.

• Turn rocker switch to HEAT mode.

• Push Night button to activate. The moon

icon will show in display screen. The “night/

away” setpoint temperature will ash for 5

seconds.

• Push the Up or Down button to

change your desired night/away set point.

• To return to your previous HEAT set point

when you awake or return, push the Night

again. The setpoint temperature will ash

for 5 seconds. The moon icon will no longer

be in display screen.

• To return to your previous night/away set-

point, simply push the Night button.

You can preset a maximum and/or minimum set point as a child

safety or tamper proof option. To preset a maximum setpoint:

• Move rocker switch to NO HEAT mode.

• Press and hold both the Night button and the Up button

at the same time, for at least 5 seconds, until the “HL” (high

limit) is displayed.

• Release buttons: temperature setpoint will ash and alternate

with “HL” on the display.

• Using the Up or Down button, set your maximum de-

sired set point.

• Turn rocker switch back to HEAT mode.

• To remove the lock, follow same instructions, and set to maxi-

mum of 90 degrees.

• To preset a minimum set point, follow same steps, but press

and hold both the Night and Down buttons until the “LL”

(low limit) is displayed.

Using the rocker switch, you can move the switch to three

modes.

CENTER POSITION: NO HEAT MODE

After a brief cool down period (up to 4 minutes), the heater will

shut down. It will not resume heating until the rocker switch is

ipped to the HEATING (left) position.

LEFT POSITION: HEAT MODE

Your ComPak Energy Plus heater has a unique variable speed

blower that auto adjusts the heat output based on the room’s

requirements. Once you set the thermostat to your desired tem-

perature, the heater will vary the wattage output for maximum

efciency.

The digital display will show the level of heat being output to

maintain the room’s temperature.

RIGHT POSITION: FAN ONLY MODE

The FAN ONLY mode can circulate air but will not supply heat.

Three fan speeds are available. To adjust the fan speed: With

rocker switch in the RIGHT position, push top (+) or bottom (-)

digital buttons up or down. Display will read “1” for low speed,

“2” for medium speed, or “3” for high speed during the set up

process, then resume to temperature display.

• Turn rocker switch to HEAT mode.

• Touch the up button or the down button

to set your desired temperature.

Temperature Setpoint Range: 40˚F - 90˚F

Rocker Switch

No Heat, Cool Down No Heat

fan is animated

Heating Full Power

Heating Mid Power Heating Low Power

Fan Only / No Heat

NIGHT /

AWAY

Night/Away

Button

Night/Away Mode

Fan Operation

Fahrenheit Setting

Night/Away Mode

Icon

Proportional Heat

Control Indicator

Heating

Mode

Indicator

Temperature

Fan Mode

Indicator

HEAT

NO FAN

NO HEAT

FAN

ONLY

FAN

ONLY

NO FAN

NO HEAT

HEAT

NIGHT /

AWAY

Rocker Switch

Night Button

Digital Display

Up Button

Down Button

Down

Page 6

1 2 3 4 5 6 7 8 9 10 11 ... 15 16

Comentarios a estos manuales

Sin comentarios

Cadet CEC163TW Guía de instalación Pagina 6

Comentarios a estos manuales

Relacionado con productos y manuales para Calentadores espaciales Cadet CEC163TW